#Zydas zd1211 driver update
#Zydas zd1211 driver driver

Plug in dongle (can be plugged in before insmodding the module). Make sure all wlan modules and ndiswrapper are unloaded.

I need to use the built-in (PS/2) mouse when using the ZYDAS dongle. Trying to use a mouse leads to very slow operation & a lot of 'hotplug' messages on the console (or visible in dmesg). 22 2008,12:14 One other issue I have noticed with the Zydas dongle - I can't use a USB mouse in the second port on the PCMCIA USB2.0 card I use.

#Zydas zd1211 driver driver

I'm a newbie and I'm not able to compile the driver from sources. I had the zd1211.o file from the site posted several messages ago from andrewb (the release for kernel 2.4.31, because now I'm using DSL 4.2.5) and I copied it into /lib/modules/2.4.31/kernel/drivers/usb/ Zd1205: (exit) zd1205_close, src/zd1205.c line 4848ДЄfter 'Operation failed' the green led on the usb dongle stop blinking, but restart if I put 'sudo ifconfig eth0 up' Zd1205: (exit) zd1205_init, src/zd1205.c line 8293Д¬ode sudo ifconfig eth0 sudo iwlist scanД®xtra:SignalStrength=81 %,LinkQuality:96%Д«it sudo iwconfig eth0 essid mylan mode sudo killall sudo pump -i eth0 Hub.c: new USB device 00:07.2-1, assigned address 2 This is the seqence of the commands I put without the pcmcia lan card, and the results I have had:

#Zydas zd1211 driver update

Have you loaded the firmware update to the correct location (download the zd1211-firmware file I have uploaded along with the modules files & look at the readme file in there), I don't know if that may help you? So far as I know the firmware update isn't actually written to you usb stick so it can't corrupt anything there, you just need the files available whenever you use the device. After that plug in the dongle & you should see it recognised with messages appearing on the console (make sure you have a terminal window open, or do this testing without X running).ДЇrom it looks like you are using the correct module (zd1211, NOT the zd1211b version). Do you have another net card in the system that makes your wifi connection eth1, rather than eth0? What result do you get from 'iwlist scan'? What order are you loading the module / plugging in the wifi dongle? Try loading the module without the dongle plugged in - you should get a nice ascii ZYDAS logo on the console (I use insmod, rather than modprobe). I use the driver I uploaded & the instructions I gave earlier in the thread. 19 2008,00:41 I have a generic usb wifi stick with the Zydas (ID 0ACE:1215) chip in it running on a Toshiba libretto (P-I, 166MHz, 64Mb). The system runs really slow & 'ps' reports many many instances of the usb hotplug scripts running. I run mine through a pcmcia USB 2.0 card & find i can't run a usb mouse through the same card at the same time as the zydas dongle. Have a look at the output of the command 'lsusb' My zydas dongle is listed as '0ace:1215'. If you are still having problems it may be that you have a different zydas chip. To get it to work with the zydas dongle you need the switch '-Dzydas'. If you want to use WPA used the version of wpa_supplicant I uploaded (in the. This will get you connected on a system with no WEP or WPA. ndiswrapper, wlan_tkip, ath_hal, etc) unloaded then load zd1211b & insert the dongle. make sure you have all other wireless lan modules (e.g. I use the zd1211b module (using to post this message!). 09 2008,12:48 The binaries are in the files I uploaded - make sure you check in the file '.for kernel 2.4.26.tar.gz'. , Vendor (the Driver don't work with Kernel 2.4):Дriver Vendor Product USB Vendor USB Product No I have try to compile the Zydas Driver with DSL 3.4.11, but I become Error.Д®veryone use the Zdydas ZD1211 with Damn Small Linux 3.4.11 oder DSL 4.2.x?